Remote cell system requirements
The remote cell can be installed on the following operating systems:
Hardware requirements
Remote cell requirements for Microsoft Windows
Component | Requirement |
|---|---|
Hard disk space | 750 MB |
RAM | 4 GB |
Common requirements for all UNIX-based Remote cells
Component | Requirement |
|---|---|
Hard disk space | 900 MB |
Software disk space | 300 MB |
Data disk space | 100 MB |
Temporary disk space (/tmp) | 100 MB |
File descriptor | 4096 |
In addition to the requirements in the table above, you must also satisfy these requirements:
- The root partition should not be full
- Umask should be 022
- BMC recommends that the TCP Control Port be set to 12124
Remote cell requirements for Linux
Component | Requirement |
|---|---|
Memory | 4 GB |
Swap space | 1 GB |
Remote cell requirements for Solaris
Component | Solaris |
|---|---|
Memory | 4 GB |
Swap space | 1 GB |
Operating system requirements
Support for third-party products
To receive full support for a BMC product, you must have such product installed in a supported environment, as specified in the BMC product documentation. If a third-party vendor cancels support for one of its products (such as an operating system or subsystem), and that third-party product integrates or interacts with the BMC product you have licensed, you must upgrade to a supported version of that third-party product before BMC Customer Support can provide you with support for the affected BMC product. For further information, see
BMC's product support policy.
Microsoft Windows
| Component | Requirement |
|---|---|
| User Rights | Administrative privileges |
| Supported versions of Microsoft Windows | Microsoft Windows 2019
Microsoft Windows 2016
Microsoft Windows 2012
Microsoft Windows 2008
Note: For Microsoft Windows 2008 and later, User Access Control must be disabled. |
Linux
| Component | Requirement |
|---|---|
| User Rights | root privileges |
| Supported versions of Linux |
|
The preferred method to add any missing libraries is to use the yum command to fetch the necessary library packages from the RHN (Red Hat Network) repository via the internet. To use this method, a Red Hat subscription is needed. Register the system by clicking System->Administration->Red Hat Subscription Manager in the menu on the server itself. After registering the system, you can use "yum install" to download and install the required libraries from the RHN.
Library | Command to install the library on Red Hat Enterprise Linux | Command to install the library on SUSE Linux |
|---|---|---|
libXtst (64-bit) | yum install libXtst.x86_64 libXtst-1.0.1-3.1 libX11-devel-1.0.3-11.el5 | N/A |
glibc (32-bit) glibc (64-bit) | glibc-devel-2.5-65 | zypper install glibc-32bit glibc |
libstdc++ (64-bit) | yum install libstdc++.x86_64 | zypper install libstdc++ |
compat-libstdc++-33 (64-bit) | yum install compat-libstdc++-33.x86_64 | zypper install libstdc++33 |
compat-libstdc++-296 (64-bit) | yum install compat-libstdc++-296.x86_64 | N/A |
pam (64-bit) | yum install pam.x86_64 | zypper install pam |
| libfreebl3.so | yum install libfreebl3.so | N/A |
Note
- To avoid errors while installing 32-bit libraries, BMC recommends that you install 32-bit libraries together with the 64-bit libraries.
- After installing the libraries, run
yum checkto ensure that the libraries are not corrupt.
Solaris
| Component | Requirement |
|---|---|
Platform | SPARC sun4v |
Operating system | Solaris 11.x (64 bit) |
Comments
Log in or register to comment.