Messages Produced by the Installation Program


These messages are issued during Strobe installation by the Compuware JCL Customization Facility. For information about installing Strobe, refer to the Strobe Installation and Configuration Guide.

STRI001E The dataset name this REXX exec STRINST is being invoked from cannot be automatically determined. Please refer to manual dataset name specification.

Explanation: The Strobe JCL customization process requires that the STRINST exec be directly invoked from the ISPF command line.

System Action: The Strobe JCL customization process does not execute.

User Response: Invoke the Strobe installation exec (STRINST) from the ISPF command line as follows:

TSO EX ‘dsn(STRINST)’.
where dsn is the dataset name of the Strobe control dataset.

STRI002E Do not invoke this REXX exec STRINST by installing it in your SYSPROC DD. Please execute it via: "TSO EX dsn(STRINST)"

Explanation: The Strobe JCL customization process requires that the STRINST exec be directly invoked from the ISPF command line.

System Action: The Strobe JCL customization process does not execute.

User Response: Invoke the Strobe installation exec (STRINST) from the ISPF command line as follows:

TSO EX ‘dsn(STRINST)’.
where dsn is the dataset name of the Strobe control dataset.

STRI003E STRINST must be run in an ISPF environment. Please start ISPF prior to running STRINST.

Explanation: The Strobe customization process requires that the STRINST exec be directly invoked from the ISPF command line.

System Action: The Strobe JCL customization process does not execute.

User Response: Invoke the Strobe installation exec (STRINST) from the ISPF command line as follows:

TSO EXEC ‘dsn(STRINST)’.
where dsn is the dataset name of the Strobe control dataset.

STRI004E The specified installation dataset dsn – could not be located ! Please verify the dataset name and try again.

Explanation: The dataset name specified in the message returned a status of DATASET NOT FOUND to the REXX function SYSDSN.

System Action: The Strobe JCL customization process does not execute.

User Response: Ensure that the installation dataset is available.

STRI005E The specified installation dataset dsn – does not contain the REXX exec "STRINST".
Please verify the dataset name and try again.

Explanation: The dataset name specified in the message returned a status of MEMBER NOT FOUND to the REXX function SYSDSN.

System Action: The Strobe JCL customization process does not execute.

User Response: Ensure that the installation dataset contains the member STRINST.

STRI006E The specified installation dataset dsn – is invalid! Reason: <reason text> Please verify the dataset name and try again.

Explanation: The dataset name specified in the message returned an error status <reason text> from the REXX function SYSDSN.

System Action: The Strobe JCL customization process does not execute.

User Response: Correct the error as denoted by the reason text. For more information on the possible reason text refer to the appropriate IBM REXX Reference space.

STRI007E The specified installation dataset dsn – does not contain the REXX exec "STRBUILD".
Please verify the dataset name and try again.

Explanation: The REXX function SYSDSN returned a status of MEMBER NOT FOUND.

System Action: The Strobe JCL customization process does not execute.

User Response: Ensure the installation dataset contains the member STRBUILD.

STRI020E STRBUILD must be run in an ISPF environment. Please start ISPF prior to running STRINST.

Explanation: The Strobe JCL customization process requires that the STRINST exec be directly invoked from the ISPF command line.

System Action: The Strobe JCL customization process does not execute.

User Response: Invoke the Strobe installation exec (STRINST) from the ISPF command line as follows:

TSO EXEC ‘dsn(STRINST)’.
where dsn is the dataset name of the Strobe control dataset.

STRI021E A fatal I/O error has occurred. Please correct the problem and try again.

Explanation: The REXX function EXECIO issued a return code = 20 when attempting to access the installation control dataset.

System Action: The Strobe JCL customization process does not execute.

User Response: Correct the error as denoted by the return code. For more information on the possible return code refer to the appropriate IBM REXX Reference space.

STRI050E Please select a product for JCL customization.

Explanation: No S in the selection field to select a product for JCL customization.

System Action: The Strobe JCL customization process does not execute.

User Response: Place an S in the selection field to select a product for JCL customization.

STRI051E A product feature can not be selected without the product base.

Explanation: One or more product features were selected without the product base function also being selected.

System Action: The Strobe JCL customization process does not execute.

User Response: Place an S in the selection field for the product base function in addition to any product features that were selected.

STRI101E  The SMS parameter must be "YES" or "NO".

Explanation: You specified an invalid value for the SMS parameter.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value of either YES or NO in the SMS parameter field.

STRI102E The DASD unit parameter contains an invalid character.

Explanation: The DASD unit parameter you specified contained one or more non-alphanumeric characters.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the DASD unit field that contains only alphanumeric characters.

STRI103E The DASD volser field contains and invalid character.

Explanation: The DASD volser parameter you specified contained one or more non-alphanumeric characters.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the DASD volser field that contains only alphanumeric characters.

STRI104E The SMP/E Work Unit parameter contains an invalid character.

Explanation: The SMP/E work unit parameter you specified contained one or more non-alphanumeric characters.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the SMP/E work unit field that contains only alphanumeric characters.

STRI105E The tape volser is missing, invalid, or less than 6 characters.

Explanation: The tape volser parameter is either missing, contained one or more non-alphanumeric characters, or was less than 6 characters in length.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the tape volser field that is 6 characters long and contains only alphanumeric characters.

STRI106E The tape unit parameter contains an invalid character.

Explanation: The tape unit parameter you specified contained one or more non-alphanumeric characters.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the tape unit field that contains only alphanumeric characters.

STRI107E The TMS parameter must be either "YES" or "NO".

Explanation: The TMS parameter you specified is invalid.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the TMS field that is either YES or NO.

STRI108E The Global High-level qualifier is not a valid dataset name.

Explanation: The Global High-level parameter suffixed with .CSI that you specified is invalid, as reported by the SYSDSN REXX function.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a valid value in the Global High-level qualifier field.

STRI200E At least one SMS parameter must be specified.

Explanation: None of the three possible SMS parameters (STORCLAS, DATACLAS, and MGMTCLAS) must be specified. You must specify at least one.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in at least one of the three SMS parameter fields.

STRI201E SMS <smsparm> parameter contains an invalid character.

Explanation: The SMS parameter <sysparm> contains one or more non-alphanumeric characters.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the SMS parameter field that contains only alphanumeric characters.

STRI301E The Global CSI dataset name is invalid.

Explanation: The Global CSI dataset name you specified is invalid, as reported by the SYSDSN REXX function.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a valid value in the Global CSI dataset name field.

STRI302E It is an SMP/E requirement that this dataset name must end with a .CSI

Explanation: The Global CSI dataset name you specified is invalid because it does not have .CSI as its last qualifier.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the Global CSI dataset name field that has .CSI as its last qualifier.

STRI303E A new Global CSI dataset name cannot be longer than 38 characters.

Explanation: The Global CSI dataset name you specified is too long. The dataset name length cannot exceed 38 characters.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the Global CSI dataset name field that does not exceed 38 characters in length.

STRI304E The CSI set-up field must be "Y" or "N".

Explanation: The value you supplied in the Global CSI set-up field is invalid.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the Global CSI set-up field that is either Y or N.

STRI501E The High-level Qualifier is not valid for a dataset name.

Explanation: The High-level Qualifier you specified is invalid, as reported by the SYSDSN REXX function.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the High-level Qualifier field that is valid.

STRI601E The Distribution Zone Name is invalid.

Explanation: The Distribution Zone name you specified is invalid, it contains one or more non-alphanumeric characters.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the Distribution Zone name that contains only alphanumeric characters.

STRI602E The Distribution Zone CSI dataset name is invalid.

Explanation: The dataset name for the Distribution Zone name you specified is invalid, as reported by the REXX SYSDSN function.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the Distribution Zone dataset name that is valid.

STRI603E It is an SMP/E requirement that the DZone DSN must end with a .CSI

Explanation: The Distribution Zone CSI dataset name you specified is invalid because it does not have .CSI as its last qualifier.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the Distribution Zone CSI dataset name field that has CSI as its last qualifier.

STRI605E The Target Zone Name is invalid.

Explanation: The Target Zone name you specified is invalid because it contains one or more non-alphanumeric characters.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the Target Zone name that contains only alphanumeric characters.

STRI606E The Target Zone CSI dataset name is invalid.

Explanation: The dataset name for the Target Zone name you specified is invalid, as reported by the REXX SYSDSN function.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a valid value for the Target Zone dataset name.

STRI607E It is an SMP/E requirement that the Target Zone DSN must end with a .CSI

Explanation: The Target Zone CSI dataset name you specified is invalid because it does not have .CSI as its last qualifier.

System Action: The Strobe JCL customization process does not process the request.

User Response: Enter a value in the Target Zone CSI dataset name field that has .CSI as its last qualifier.




 

Tip: For faster searching, add an asterisk to the end of your partial query. Example: cert*