Image copy options

This topic describes the options that enable image copies during a load job.

COPY

The COPY option tells BMC AMI Load whether to produce a copy of the table space or selected partitions during the load.

Operands

The unit name and options for the copy destinations are defined by the one of the following methods. The value of the OVERRIDEOUTPUT parameter determines the method that BMC AMI Load uses.

• The XCPYDYNM-dynamic-image-copy-data-set-allocation-automation-control-point (either directly or by using the NGTTAPE command)
• The OUTPUT commandYou must place the OUTPUT command before the LOAD statement in your SYSIN.

The following considerations apply to the COPY option:

• You cannot specify COPY if you specify RESUME YES SHRLEVEL CHANGE.
• You must specify the OUTPUT command, or the XCPYDYNM automation control point must be available to provide the image copy data set name for each image copy.
• BMC AMI Load registers all copies with Db2 in the SYSIBM.SYSCOPY table. 
• BMC AMI Load ignores any INLINE specification.

COPYPEND

This option is available only if you specify COPY NO.

The COPYPEND option specifies whether BMC AMI Load should set the table space to COPY pending status if a copy was not made as part of the load job.

When COPYPEND is not specified, the +COPYPENDING parameter setting takes effect. For more information, see COPYPENDING .

Operands

COPYDDN(lp,lb)

COPYDDN(lp,lb) tells BMC AMI Load to produce a primary and, optionally, a backup copy to the indicated local copy destinations.

The first value specifies a local primary (lp) copy; the second value specifies a local backup (lb) copy. If you specify COPYDDN, you must specify at least a local primary copy.

These values do not specify a DD name; they signify the intention to produce a copy to this destination. The actual unit name and options for the copy destinations are defined by the one of the following methods. The value of the OVERRIDEOUTPUT parameter determines the method that BMC AMI Load uses.

• The XCPYDYNM-dynamic-image-copy-data-set-allocation-automation-control-point (either directly or by using the NGTTAPE command)
• The OUTPUT commandYou must place the OUTPUT command before the LOAD statement in your SYSIN.

The following considerations apply to COPYDDN:

• You cannot specify COPYDDN if you specify RESUME YES SHRLEVEL CHANGE.
• (BMC.DB2.SPE2207) If copy datasets are not defined in the JCL, you must specify the OUTPUT-command-for-BMC-AMI-Load, or the XCPYDYNM-dynamic-image-copy-data-set-allocation-automation-control-point must be available to provide the image copy data set name for each image copy.

• (BMC.DB2.SPE2207)

   

  BMC AMI Load

   supports COPY datasets defined in the JCL when loading a single partition or a non-partitioned table space. 

• The parentheses are optional if you specify only one destination name (for example, COPYDDN LP1); the parentheses are required if you specify two DD names.
• COPYDDN specified before the INTO TABLE can have two positional parameters, for example COPYDDN (A,B). COPYDDN coded after the INTO TABLE can have only one positional parameter, for example COPYDDN(A).

• The following table shows the partitions that BMC AMI Load copies:

  Command	Partition copied
  LOAD DATA INDDN SYSREC REPLACE COPYDDN(A) INTO TABLE A.B	Whole table
  LOAD DATA INDDN SYSREC RESUME YES COPYDDN(A) INTO TABLE A.B	Only the partitions that are loaded
  LOAD DATA INDDN SYSREC RESUME YES INTO TABLE A.B PART X REPLACE COPYDDN(A)	Only the partitions that are loaded
  LOAD DATA INDDN SYSREC RESUME YES COPYDDN(A) INTO TABLE A.B PART X REPLACE	Only the partitions that are loaded
  LOAD DATA INDDN SYSREC INTO TABLE A.B PART X REPLACE COPYDDN(A)	Only partition X

RECOVERYDDN(rp,rb)

RECOVERYDDN(rp,rb) tells BMC AMI Load to produce a primary and, optionally, a backup copy to the indicated remote copy destinations.

The first value specifies a remote primary (rp) copy; the second value specifies a remote backup (rb) copy.

These values do not specify a DD name; they signify the intention to produce a copy to this destination. The actual unit name and options for the copy destinations are defined by one of the following methods. The value of the OVERRIDEOUTPUT parameter determines the method that BMC AMI Load uses.

• The  XCPYDYNM-dynamic-image-copy-data-set-allocation-automation-control-point (either directly or by using the NGTTAPE command)
• The OUTPUT commandYou must place the OUTPUT command before the LOAD statement in your SYSIN.

The following requirements and considerations apply to the RECOVERYDDN option:

• You cannot specify RECOVERYDDN if you specify RESUME YES SHRLEVEL CHANGE.
• (BMC.DB2.SPE2207) If copy datasets are not defined in the JCL, you must specify the OUTPUT-command-for-BMC-AMI-Load, or the  XCPYDYNM-dynamic-image-copy-data-set-allocation-automation-control-point must be available to provide the image copy data set name for each image copy.

• (BMC.DB2.SPE2207)

   

  BMC AMI Load

   supports COPY datasets defined in the JCL when loading a single partition or a non-partitioned table space. 

• The parentheses are optional if you specify only one destination name. The parentheses are required if you specify two DD names.