Troubleshooting Patch Management issues

STDERR: cat: rpm-includes.lst: No such file or directory ERROR::YUM dry run failed. ERROR::cmd: failed!

{{code language="none"}}
Missing Dependency: [rpm1] = [version] is needed by package [rpm2-version.arch] (installed)
{{/code}}

{{code language="none" source="string:{{code language=~"none~"~}~}
Missing Dependency: [rpm1] = [version] is needed by package [rpm2-version.arch] (repo)
{{/code~}~}"/}}
{{/code}}
)))
|(((
**Description**
)))|(((
Neither rpm1 of the specified version nor rpm2 are installed on the target. Yum sets rpm2 to be updated for one of two reasons:

* Yum detected an older version of rpm2 installed.
* Yum offered rpm2 as a dependency to some other rpm.

Yum checks if rpm2 needs any dependencies of its own, and detects that rpm1 of the specified version is needed as a dependency. Therefore, yum attempts to set rpm1 to be updated as well, but fails. An error is logged, alerting that rpm1 is required for rpm2 to be installed.
)))
|(((
**Troubleshooting**
)))|(((
To troubleshoot this error, follow these steps:

1. Check if rpm1 of the specified version exists in the Catalog.
1. If rpm1 is not in the Catalog, check if it exists in the RHN Channel.
1*. If not in RHN Channel, then analysis happens as expected.
1*1. Acquire rpm1 by other means and install it manually.
1*1. Exclude rpm2 from the analysis or uninstall rpm2.
When you uninstall rpm2, consult your administrator and use caution.
Note that another rpm might require the newer version of the excluded rpm. Furthermore, this step will not work if yum offered rpm2 as a dependency to some other rpm.
1*. If present in the RHN Channel, run the Catalog Update Job again.
1*1. If rpm1 is still not in catalog, and this is not an RBAC-related issue, then collect logs and contact BMC Support.
1*1. If rpm1 is now present in the catalog, run the analysis again.
If Analysis still shows the same error, continue to the next step.
1. If rpm1 is present in the catalog, check whether rpm1 is present in **repodata.tar.gz** on the target by running the following command:{{code language="none"}}# cd <staging>/LinuxCatalog_XXX_[target]/{{/code}}{{code language="none"}}# yum -C -c yum.conf search [rpm1]

{{/code}}Proceed according to the results that you obtain:
1*. If rpm1 is not found, then this could be why it is not offered during Analysis.
1*. If rpm1 is found, something might be preventing it from being installed.
In such a case, try performing a //dry run// installation of rpm1 using the following command:
{{code language="none"}}# rpm -iUv --test rpm1{{/code}}
If the dry run fails, then yum predicted this failure and that is why yum rejected rpm1 from being updated, and rpm1 was no longer considered to be updated. An error is logged, indicating rpm1 as a missing dependency. For a possible cause for this dry run failure, see [[Knowledge Article KA347757>>url:https://kb.bmc.com/infocenter/index?page=content&id=KA347757||shape="rect"]].
)))
|(((
**Logs to collect**
)))|(((
(% class="O1" %)
(((
**Log files to collect from the application server**
)))

(% class="O1" %)
(((
Patch Analysis Job log
\\
)))

(% class="O1" %)
(((
(% class="O1" %)**Log files to collect from the target**
)))

* rscd.log
* analysis bundle.log (including repodata.tar.gz)
* rpm –qa
)))

{{export-ignore}}
,,[[Back to top>>doc:||anchor="TroubleshootingPatchManagementissues-Top"]],,
{{/export-ignore}}

==== {{id name="TroubleshootingPatchManagementissues-Yumfailedtocomplete-Scenario3"/}}Yum failed to complete - Scenario 3 ====

The following scenario describes an error where the yum file fails to complete, as well as steps to troubleshoot the issue.

|(((
**Error Message**
)))|(((
(% style="margin-left: 0.3in;" %)
(((
{{code language="none"}}[rpm1] conflicts with [rpm2]{{/code}}
(% style="color: black;" %)
)))
)))
|(((
**Description**
)))|(((
Rpm2 is installed on the target, while rpm1 is not. Yum attempts to offer rpm1 to be installed or updated, but then yum detects that some of the files to be updated by rpm1 are used by rpm2. Therefore, yum rejects the installation or update of rpm1. An error is logged, alerting that rpm1 cannot be installed. In general, the conflict suggests that rpm1 and rpm2 cannot coexist if rpm versions matter.
)))
|(((
**Troubleshooting**
)))|(((
1. Check the RHN site for known conflict issues.
A conflict may arise if either rpm1 or rpm2 are not in the repository.
1. Validate that the rpm is in RHN channel, in the Catalog, and in **repodata.tar.gz**, as described in [[scenario 2>>doc:||anchor="TroubleshootingPatchManagementissues-Yumfailedtocomplete-Scenario2"]].
Note that resolution cannot be guaranteed if the RPMs come from different channels.
1. Proceed according to your needs:
1*. If rpm1 must be installed, check whether rpm2 can be uninstalled, downgraded, or upgraded to a non-conflicting version.
1*. If rpm2 must be preserved, consider the following actions:
1**. Check whether rpm1 can be excluded. Note that another rpm might require the newer version of the excluded rpm.
1**. Check whether another non-conflicting version of rpm1 can be installed.
1**. Check whether multiple versions of rpm2 are installed, where the conflicting one can be uninstalled.
1. If the previous steps do not resolve the problem, collect logs and contact BMC Support.
)))
|(((
**Logs to collect**
)))|(((
(% class="O1" %)
(((
**Log files to collect from the application server**
)))

(% class="O1" %)
(((
Patch Analysis Job log
\\
)))

(% class="O1" %)
(((
(% class="O1" %)**Log files to collect from the target**
)))

* analysis bundle.log (including repodata.tar.gz)
* rpm –qa
)))

{{export-ignore}}
,,[[Back to top>>doc:||anchor="TroubleshootingPatchManagementissues-Top"]],,
{{/export-ignore}}

=== {{id name="TroubleshootingPatchManagementissues-DeployJobfailedscenarios"/}}Deploy Job failed scenarios ===

==== {{id name="TroubleshootingPatchManagementissues-DeployJobfailed-Scenario1"/}}Deploy Job failed - Scenario 1 ====

|(((
**Error Message**
)))|(((
{{code language="none"}}
[rpm-version.arch]: Caching enabled but no local cache of //<staging>/blrepos/repo/packages/[rpm-version.arch].rpm from repo
{{/code}}
)))
|(((
**Description**
)))|(((
Prior to installing the packages, the Deploy Job runs a preliminary yum analysis. During this analysis scan, **rpm-version.arch** is found as missing. The Deploy Job does not find **rpm-version.arch** in the list of staged missing patches, and, therefore, the job cannot proceed.

An error is logged, alerting you that the patch payload is not found and cannot be installed. This error indicates that a discrepancy was found between the regular Patch Analysis and the preliminary yum scan during Deploy, or that **rpm-version.arch** was not copied during staging. The error message is written in either the Deploy Job log or the **bldeploy** log.
)))
|(((
**Troubleshooting**
)))|(((
1. Review Patch Analysis results and check whether **rpm-version.arch** was found as missing.
1. If the file is missing, check whether it was packaged during patch remediation.\\
1*. If it was packaged, check whether it points to an existing source. Open the object from inside the Catalog and review its **Installable source** value.\\
1**. The root cause of the problem might be that the installable source //points to a missing payload//. In this case, rerun the Catalog or download the patch manually.
1**. If the source points to an //available payload//, review the stage phase of the Deploy Job. Check for issues that might have occurred during the copying of the payload to the target.
1*. If the object was not packaged, check for possible RBAC issues.
1. (((
If patch was not found missing, compare yum scans of Analysis and Deploy:

* Analysis: **<staging>/LinuxCatalog_XXX_[target]/yum_analysis.res**
* Deploy: **<staging>/XXXXX/blres.yum.depl**



{{confluence_note}}
The deploy log exists if the Deploy Job was set to //preserve staging area on failure//. If not, configure this setting now, then reproduce the error and collect the log file.
{{/confluence_note}}
)))
1. Compare the lists of //set to be updated// patches.
This comparison might reveal that for some RPMs, the analysis finds one **arch** file missing, while Deploy finds the other one missing. This might be the cause of the original issue. If so, a fix is available in BMC Server Automation 8.1 Service Pack 3.
1. If the preceding steps did not reveal the root cause of the issue, collect several logs and contact BMC Support. From the application server, obtain the Patch Analysis Job log. In addition, obtain the following logs from the target:
1*. Analysis bundle log
1*. bldeploy log
1*. **<staging>/XXXXX/blres.yum.depl**
)))

{{export-ignore}}
,,[[Back to top>>doc:||anchor="TroubleshootingPatchManagementissues-Top"]],,
{{/export-ignore}}

==== {{id name="TroubleshootingPatchManagementissues-DeployJobfailed-Scenario2"/}}Deploy Job failed - Scenario 2 ====

|(((
**Error Message**
)))|(((
(% style="margin-left: 0.3in;" %)
(((
(% class="code" %)
(((
package [rpm-version] is already installed
)))

(% style="color: black;" %)
)))
)))
|(((
**Description**
)))|(((
(% class="O1" %)
The Deploy Job installs the patches that were found missing during Analysis. In this case, the Analysis Job packaged the rpm-version, even though it is already installed.
)))
|(((
**Troubleshooting**
)))|(((
1. (((
Review the Analysis logs to troubleshoot the issue. 

(% class="O1" %)
(((
The error message is located in either the Deploy Job log or the bldeploy log.
You might see the following log records:
)))

* The analysis_log.log is expected to reveal that the Patch Analysis ran with an include filter. The signs for this are:\\
** After 'update' you see a list of RPMs.
** YUM Command: for i in 0 1 2 3 4 5 :; {{code language="none"}}do echo n; done | blyum -c ./yum.conf -C update "rpm-version.arch" "…" ...{{/code}}
* Command {{code language="none"}}rpm –q [rpm]{{/code}} reveals that multiple versions of the rpm are installed.
)))
1. The expected findings described in the previous step are not the standard configuration. Therefore, perform the following further testing:
1*. Run yum update with include list.
This is expected to produce the following error:{{code language="none"}}latest rpm as missing{{/code}} [issue reproduced]
The updated rpm is offered for the older version of RPM that is installed even if the new version is also already installed.
1*. Run yum update without include list.
This should return the following message:{{code language="none"}}no missing rpm{{/code}} [good result]
If we do not forcefully analyze for patches (with an include filter), then if the latest version is found, the rpm is not offered.
1*. Run yum install with include list.
This should return the following message:{{code language="none"}}no missing rpm{{/code}} [good result]
The //Install// option checks only for the specific version of the rpm that we are attempting to install. Since our specific version of rpm is already installed, it will not be installed again.
1. If you must preserve multiple versions of such RPMs, create a separate analysis job where you would use //Install //option and include the RPM.
1. Modify the existing Analysis Job include filter and remove the RPM.
If the RPM must be included, try excluding the opposite set of RPMs. For example, exclude all where RPM does not equal [rpm-version].
1. Yum does not install multiple versions of such RPMs by default, so if they are not required, then uninstall the old versions.
The Analysis Job should no longer report the latest RPM as missing, because there will no longer be multiple versions.
)))
|(((
**Logs to collect**
)))|(((
(% class="O1" %)
(((
**Log files to collect from the application server**
)))

(% class="O1" %)
(((
* Patch Analysis Job log
)))

(% class="O1" %)
(((
(% class="O1" %)**Log files to collect from the target**
)))

(% class="O1" %)
(((
* analysis bundle log
* bldeploy log
* <staging>/XXXXX/blres.yum.depl
* rpm –q [rpm]
)))
)))

{{export-ignore}}
,,[[Back to top>>doc:||anchor="TroubleshootingPatchManagementissues-Top"]],,
{{/export-ignore}}

== {{id name="TroubleshootingPatchManagementissues-Thirdpartyissuesandlimitationsforpatchmanagement"/}}Third party issues and limitations for patch management ==

{{excerpt-include 0="Automation-DevSecOps.Server-Automation.Server-Automation.bsadoc.Using.Patch-management.Special-issues-for-patch-management.WebHome" name="third_party_patch_issues" nopanel="true"/}}

{{export-ignore}}
,,[[Back to top>>doc:||anchor="TroubleshootingPatchManagementissues-Top"]],,
{{/export-ignore}}

== {{id name="TroubleshootingPatchManagementissues-Relatedtopics"/}}Related topics ==

[[doc:Automation-DevSecOps.Server-Automation.Server-Automation.bsadoc.Using.Patch-management.Special-issues-for-patch-management.WebHome]]\\