Page tree
Skip to end of metadata
Go to start of metadata

The Device Performance dashlet displays the performance metrics of a single device based on selected parameters. For each device, you can view a maximum of four parameters. Each parameter is displayed in a separate chart. The charts are displayed based on the number of parameters configured.

Related topics

Dashlet library

Adding and modifying dashboards

Adding and editing components

A Device Health Bar chart is displayed below the parameter charts, displaying the severity counts based only on critical, major, and minor events and belonging only to open, acknowledged, and assigned statuses. If there are zero severities, a green bar is shown indicating a good health and a non-zero number displays a segmented bar chart with the event count against each severity as shown in these figures.


On the parameter charts, click a data point to open the Monitor Details page and on the Device Health bar chart as shown in the figure.

 

 

On the Device Health chart, clicking the segmented chart data opens the Device Details page as shown in the figure. However, a Device Health with a green bar is not clickable.

Dashlet requirements

At least one instance of a TrueSight Infrastructure Manager server must be registered with the Presentation Server forthisdashlet template to be available.

Configuring the dashlet

You can configure this dashletwhenyou add or edit a dashboard .

  1. Click Add Dashlet and select the Device Performance dashlet.
  2. Click the Configure Dashlet  icon.

  3. Enter a meaningful and descriptive Title forthedashlet.
  4. From the Refresh Rate list, select a frequency for refreshing the chart view.
    The default is 5 minutes.

  5. Click the (Select) link to select a Device.

    A device search dialog box is opened with a list of devices.

  6. Either select a device from the list or type the name of a device to search, select it, and click OK.
    The device name is displayed with a (Change) link next to it. You can change the device by clicking the link or proceed to the next step.
    As soon as the device is selected, the parameters for that device are listed under the Available Parameters section as shown in the figure. 

    Info

    It is possible that a selected device was deleted from the TrueSight server after it was selected in this dashlet. In that case, a message (The device appears to be deleted and cannot be loaded) is displayed, and no available parameters are displayed for the device. There are two possible scenarios in this case:

    - The user did not intentionally delete the device: click the (Change) link and select the same device again.

    - The user intentionally deleted the device: delete and reconfigurethedashletagain.

  7. Enter the parameter name or first few characters in the Search Parameters field and click Search.
    For example, type Sybase as shown in the figure, to limit the number of parameters listed under the Available Parameters section.
  8. From the Available Parameters (Monitor:Type::Monitor:Attributes), you can select up to four parameters.
    The selected parameters are moved into the Selected Parameters section and the (Change) link next to the device name is replaced with a (Clear the parameters list to change the device) message. See the figure for an example.

    Note

    - To change the list of selected parameters, you must clear one or more parameters from either the Available Parameters or the Selected Parameters section, and select a different set of parameters from the Available Parameters section.

    - To change the device, first clear all the four parameters. After you clear them, the (Change) link reappears next to the device name.

    - The Monitor part shows the absolute path, only when Show absolute path for the Monitor Instances is enabled under User Preferences. .

    For example, 

    If Show absolute path for the Monitor Instances is not enabled, the Monitor path is displayed as Health AT A Glance::Health At A Glance:System Paging

    If Show absolute path for the Monitor Instances is enabled, the Monitor path is displayed as Health AT A Glance::Windows Operating System/Health At A Glance:System Paging. Notice the Windows Operating System/Health At A Glance in the path.

  9. Select the height of the dashletrow: 3X or 4X
    The value of X is approximately 100 pixels. The default height is 3X.
  10. Click Apply to add the configured dashlet to the dashboard. 

    Best practice

    After you save the Device Performance dashlet, change the dashboard row size settings to a 100% layout.

    Note

    This dashlet is not affected by the Applications global filter at the dashboard level.