Viewing result of the last scan
You can view the result of the last asset discovery scan to check the status of individual protocols. You can also check the log for each device.
To view the scan result
Navigate to Asset Discovery > Scanners > (Your scanner) > Module Configuration.
Select the Device List tab.
The following information is displayed about the last scan:
Parameter Description Status These fields display the current scan status of the respective target. If the target cannot be scanned, that is, it is not contactable, the status displays Unreachable
.Device Name The fields of this column display the names of the scan targets. IP Address The IP address of the device in its dotted version, such as 194.50.68.255. Operating System Name Name The name of the operating system installed on the discovered device. NMAPOS The field indicates the status of operating system detection via Network Mapper (NMAP). (See the legend at the bottom of the table for status information.) SSH The field indicates the status of Secure Shell (SSH) credential validation. (See the legend at the bottom of the table for status information.)
If the SSH credentials are valid, SSH is used to detect operating system, software, and hardware.
If the credential validation fails, the SSHOS, SSHSW, and SSHHW tests are not run and the corresponding columns remain empty.
SMB SMB The field indicates the status of Server Message Block (SMB) credential validation. (See the legend at the bottom of the table for status information.)
If the SMB credentials are valid, SMB is used to detect operating system and software.
If the credential validation fails, the SMBOS and SMBSW tests are not run and the corresponding columns remain empty.
WMI WMI The field indicates the status of Windows Management Instrumentation (WMI) credential validation. (See the legend at the bottom of the table for status information.)
If the credentials are valid, WMI is used to detect operating system, software, and hardware.
If the credential validation fails, the WMIOS, WMISW, and WMIHW tests are not run and the corresponding columns remain empty.
SNMP SNMP The field indicates the status of Simple Network Management Protocol (SNMP) credential validation. (See the legend at the bottom of the table for status information.)
If the SNMP credentials are valid, SNMP is used to detect operating system, hardware, and network connectivity.
If the credential validation fails, the SNMPOS, SNMPHW, and SNMPCON tests are not run and the corresponding columns remain empty.
SSHOS SSHOS The field indicates the status of operating system detection via SSH. (See the legend at the bottom of the table for status information.) SMBOS SMBOS The field indicates the status of operating system detection via SMB. (See the legend at the bottom of the table for status information.) WMIOS WMIOS The field indicates the status of operating system detection via WMI. (See the legend at the bottom of the table for status information.) SNMPOS SNMPOS The field indicates the status of oeprating system detection via SNMP. (See the legend at the bottom of the table for status information.) SSHSW SSHSW The field indicates the status of software detection via SSH. (See the legend at the bottom of the table for status information.) SMBSW SMBSW The field indicates the status of software detection via SMB. (See the legend at the bottom of the table for status information.) WMISW WMISW The field indicates the status of software detection via WMI. (See the legend at the bottom of the table for status information.) SSHHW SSHHW The field indicates the status of hardware detection via SSH. (See the legend at the bottom of the table for status information.) WMIHW WMIHW The field indicates the status of hardware detection via WMI. (See the legend at the bottom of the table for status information.) SNMPHW SNMPHW The field indicates the status of hardware detection via SNMP. (See the legend at the bottom of the table for status information.) SNMPCON SNMPCON The field indicates the status of network connectivity detection via SNMP. (See the legend at the bottom of the table for status information.) Detail This field displays the latest status of the scan. Discovery Time This column displays the date and time at which the individual devices were discovered for the first time. Start Time The date and time at which the scanning session was started on the target client. End Time The date and time at which the session finished. Duration (Sec) The the total time the session needed to execute in the regular time format hh:mm:ss. MAC Address The MAC, that is, the hardware address of the currently discovered device. Legends:
- Yellow (): Operation in progress
- Red (): Operation failed
- Green (): Operation successful
- (Empty cell): Operation not performed as the protocol credentials are either not supplied or are invalid.
To view scan log
- Right click the row for which you want to view the log and select Display Log .
The logged entries for the selected row is displayed.
Comments
Log in or register to comment.